Mini-Chat
  • User avatar
    JohnFormant - Sat Jun 17, 2017 4:10 pm

    ha i thought that message had just come up when I logged in, just realised it was from yesterday

  • User avatar
    JohnFormant - Sat Jun 17, 2017 4:11 pm

    i hope he worked it out :P

  • User avatar
    anurag2508 - Mon Jun 19, 2017 1:17 am

    Hello Everyone

  • User avatar
    anurag2508 - Mon Jun 19, 2017 1:17 am

    I am trying to interface Nodemcu Amica with Arduino IDE, But facing some issues with code upload.

  • User avatar
    anurag2508 - Mon Jun 19, 2017 1:18 am

    cn any one here help me out

  • User avatar
    Sam Denty - Wed Jun 21, 2017 5:43 am

    I have an ESP12-E module, am I able to safely connect a 3.7v LiPo directly to the ViN GND Pins?

  • Guest - Wed Jun 21, 2017 12:07 pm

    hi guys my espcopter mini programmable drone project live on indiegogo but very few people donated to the campaign :(( viewtopic.php?f=31&t=15231

  • User avatar
    tarun1996 - Sun Jun 25, 2017 12:14 am

    how to connect a 5v sensor the nodemcu board

  • User avatar
    Tushar Rajput - Sun Jun 25, 2017 5:59 am

    I have the ESP 8266 module connected to an Arduino Uno but I cannot see anything in the serial monitor....Not even the AT commands....carraige return with Baud 115200...

  • User avatar
    Tushar Rajput - Sun Jun 25, 2017 6:00 am

    Please Help

  • User avatar
    Tushar Rajput - Mon Jun 26, 2017 1:38 am

    Board: "Generic ESP8266 Module, 80 MHz, 40MHz, DIO, 115200, 512K (64K SPIFFS), ck, Disabled, None" Archiving built core (caching) in: C:\Users\TUSHAR~1\AppData\Local\Temp\arduino_cache_393385\core\core_esp8266_esp8266_generic_CpuFrequency_80,FlashFreq_40,FlashMode_dio,UploadSpeed_115200,FlashSize_512K64,ResetMethod_ck,Debug_Disabled,DebugLevel_None_____cbe5faabae27187 warning: espcomm_sync failed error: espcomm_open failed error: espcomm_upload_mem failed error: espcomm_upload_mem failed

  • User avatar
    Tushar Rajput - Mon Jun 26, 2017 1:38 am

    The error I am getting

  • User avatar
    Saumya Ranjan - Mon Jun 26, 2017 9:37 am

    hi

  • User avatar
    Saumya Ranjan - Mon Jun 26, 2017 9:37 am

    anyone can help me regarding esp8266 01e?

  • User avatar
    Saumya Ranjan - Mon Jun 26, 2017 9:41 am

    i have a DHT22 temp sensor, trying to read temp through GIO02 pin , which is in ESP2866. But its not reading. If i am connecting sensor with arduino uno board itw working but not from 8266.

  • User avatar
    Saumya Ranjan - Mon Jun 26, 2017 9:41 am

    so anyone can help me on this?

  • User avatar
    AkashAsh - Tue Jun 27, 2017 3:59 am

    getting ets Jan 8 2013,rst cause:2, boot mode:(3,6) while using Wifi.config(). Can anyone please help me with this

  • User avatar
    AkashAsh - Tue Jun 27, 2017 4:00 am

    Getting this every time trying to set static ip for my module

  • User avatar
    Tristan8686 - Tue Jun 27, 2017 4:33 am

    Hi, I wrote two answers yesterday and I do not see them published. Is it normal?

  • User avatar
    RubenFerol - Tue Jun 27, 2017 12:57 pm

    Hi, guyz. I’m new here and i have the same question as Tristan ^ . Just posted a new subject like 30 mins ago. How long will it take be published?

Who is chatting

No one is chatting  based on users active over the past 15 minutes

Refreshes every 30 seconds
Legend: Administrators, Global moderators