- Sat Apr 22, 2017 12:05 pm
#65142
Hello guys
Can someone support me on this project? I'm trying to make 4 digital inputs + 4 digital outputs at once on module ESP12E but I'm not able to make it work.
If I disable part of the code for inputs then outputs are working or oposite too however all at once looks to make module bloacket.
Thanks in advance for your help
Can someone support me on this project? I'm trying to make 4 digital inputs + 4 digital outputs at once on module ESP12E but I'm not able to make it work.
If I disable part of the code for inputs then outputs are working or oposite too however all at once looks to make module bloacket.
Thanks in advance for your help
Code: Select all
//ItKindaWorks - Creative Commons 2016
//github.com/ItKindaWorks
//
//Requires PubSubClient found here: https://github.com/knolleary/pubsubclient
//
//ESP8266 Simple MQTT light controller
#include <PubSubClient.h>
#include <ESP8266WiFi.h>
#include <EEPROM.h>
//EDIT THESE LINES TO MATCH YOUR SETUP
#define MQTT_SERVER "192.168.1.200"
const char* ssid = "JAZZTEL_david";
const char* password = "0102030405060";
// Assign Arduino Friendly Names to GPIO pins
#define D0 16 //
#define D1 5 // I2C Bus SCL (clock)
#define D2 4 // I2C Bus SDA (data)
#define D3 0
// #define D4 2 // Same as "LED_BUILTIN", but inverted logic
#define D5 14 // SPI Bus SCK (clock)
#define D6 12 // SPI Bus MISO
#define D7 13 // SPI Bus MOSI
#define D8 15 // SPI Bus SS (CS)
#define D9 3 // RX0 (Serial console)
#define D10 1 // TX0 (Serial console)
const int internalled = 2; //GPIO 2 internal led
int D0State = 0;
int D1State = 0;
int D2State = 0;
int D3State = 0;
int D5State = 0;
int D6State = 0;
int D7State = 0;
int D8State = 0;
char* Topic = "/test/light";
WiFiClient wifiClient;
// Callback function header
void callback(char* topic, byte* payload, unsigned int length);
PubSubClient client(MQTT_SERVER, 1883,callback, wifiClient);
long lastMsg = 0;
char msg[50];
void setup() {
//initialize the light as an output and set to (off)
pinMode(D0, INPUT);
pinMode(D1,INPUT);
pinMode(D2,INPUT);
pinMode(D3, INPUT);
pinMode (D5, OUTPUT);
pinMode (D6, OUTPUT);
pinMode (D7, OUTPUT);
pinMode (D8, OUTPUT);
EEPROM.begin(512); // Begin eeprom to store on/off state
D5State = EEPROM.read(0);
digitalWrite(D5,D5State);
D6State = EEPROM.read(1);
digitalWrite(D6,D6State);
D7State = EEPROM.read(2);
digitalWrite(D7,D7State);
D8State = EEPROM.read(3);
digitalWrite(D8,D8State);
pinMode(internalled, OUTPUT);
digitalWrite(internalled, HIGH);
//start the serial line for debugging
Serial.begin(115200);
delay(100);
//start wifi subsystem
WiFi.begin(ssid, password);
//attempt to connect to the WIFI network and then connect to the MQTT server
reconnect();
//wait a bit before starting the main loop
delay(2000);
}
void loop(){
//reconnect if connection is lost
if (!client.connected() && WiFi.status() == 3) {reconnect();}
//maintain MQTT connection
client.loop();
//MUST delay to allow ESP8266 WIFI functions to run
delay(10);
digitalWrite(internalled, LOW);
}
void callback(char* topic, byte* payload, unsigned int length) {
//convert topic to string to make it easier to work with
String topicStr = topic;
// Print out some debugging info
Serial.println("Callback update.");
Serial.print("Topic: ");
Serial.println(topicStr);
D0State = digitalRead(D0);
D1State = digitalRead(D1);
D2State = digitalRead(D2);
D3State = digitalRead(D3);
//turn the light on if the payload is '1' and publish to the MQTT server a confirmation message
if (payload[0] == '0'){
digitalWrite(D5, HIGH);
client.publish("/test/light1", "out1 On");
D5State = HIGH;
EEPROM.write(0, D5State); // Write state to EEPROM
EEPROM.commit();
}
//turn the light off if the payload is '0' and publish to the MQTT server a confirmation message
else if (payload[0] == '1'){
digitalWrite(D5, LOW);
client.publish("/test/light1", "out1 Off");
D5State = LOW;
EEPROM.write(0, D5State); // Write state to EEPROM
EEPROM.commit();
}
//turn the light2 on if the payload is '1' and publish to the MQTT server a confirmation message
else if (payload[0] == '2'){
digitalWrite(D6, HIGH);
client.publish("/test/light1", "out2 On");
D6State = HIGH;
EEPROM.write(1, D6State); // Write state to EEPROM
EEPROM.commit();
}
//turn the light2 off if the payload is '0' and publish to the MQTT server a confirmation message
else if (payload[0] == '3'){
digitalWrite(D6, LOW);
client.publish("/test/light1", "out2 Off");
D6State = LOW;
EEPROM.write(1, D6State); // Write state to EEPROM
EEPROM.commit();
}
//turn the light3 on if the payload is '1' and publish to the MQTT server a confirmation message
else if (payload[0] == '4'){
digitalWrite(D7, HIGH);
client.publish("/test/light1", "out3 On");
D7State = HIGH;
EEPROM.write(2, D7State); // Write state to EEPROM
EEPROM.commit();
}
//turn the light3 off if the payload is '0' and publish to the MQTT server a confirmation message
else if (payload[0] == '5'){
digitalWrite(D7, LOW);
client.publish("/test/light1", "out3 Off");
D7State = LOW;
EEPROM.write(2, D7State); // Write state to EEPROM
EEPROM.commit();
}
//turn the light4 on if the payload is '1' and publish to the MQTT server a confirmation message
else if (payload[0] == '6'){
digitalWrite(D8, HIGH);
client.publish("/test/light1", "out4 On");
D8State = HIGH;
EEPROM.write(3, D8State); // Write state to EEPROM
EEPROM.commit();
}
//turn the light4 off if the payload is '0' and publish to the MQTT server a confirmation message
else if (payload[0] == '7'){
digitalWrite(D8, LOW);
client.publish("/test/light1", "out4 Off");
D8State = LOW;
EEPROM.write(3, D8State); // Write state to EEPROM
EEPROM.commit();
}
//turn the lights off if the payload is '8' and publish to the MQTT server a confirmation message
//else if (payload[0] == '8'){
// digitalWrite(D0, LOW);
//digitalWrite(D1, LOW);
//digitalWrite(D2, LOW);
//digitalWrite(D3, LOW);
//client.publish("/test/light1", "all lights Off");
//client.publish("/test/light1", "out1 Off");
//client.publish("/test/light1", "out2 Off");
//client.publish("/test/light1", "out3 Off");
//client.publish("/test/light1", "out4 Off");
//}
//turn aa the lights on if the payload is '9' and publish to the MQTT server a confirmation message
//else if (payload[0] == '9'){
// digitalWrite(D0, HIGH);
// digitalWrite(D1, HIGH);
//digitalWrite(D2, HIGH);
//digitalWrite(D3, HIGH);
//client.publish("/test/light1", "all lights on");
//client.publish("/test/light1", "out1 On");
//client.publish("/test/light1", "out2 On");
//client.publish("/test/light1", "out3 On");
//client.publish("/test/light1", "out4 On");
//}
if (D0State == HIGH);{
client.publish("/test/light1", "input1");}
if (D1State == HIGH);{
client.publish("/test/light1", "input2");}
if (D2State == HIGH);{
client.publish("/test/light1", "input3");}
if (D3State == HIGH);{
client.publish("/test/light1", "input4");}
}
void reconnect() {
//attempt to connect to the wifi if connection is lost
if(WiFi.status() != WL_CONNECTED){
//debug printing
Serial.print("Connecting to ");
Serial.println(ssid);
digitalWrite(internalled, HIGH);
//loop while we wait for connection
while (WiFi.status() != WL_CONNECTED) {
delay(500);
Serial.print(".");
}
//print out some more debug once connected
Serial.println("");
Serial.println("WiFi connected");
Serial.println("IP address: ");
Serial.println(WiFi.localIP());
//-digitalWrite(internalledpin, LOW);
}
//make sure we are connected to WIFI before attemping to reconnect to MQTT
if(WiFi.status() == WL_CONNECTED){
// Loop until we're reconnected to the MQTT server
while (!client.connected()) {
Serial.print("Attempting MQTT connection...");
// Generate client name based on MAC address and last 8 bits of microsecond counter
String clientName;
clientName += "esp8266-";
uint8_t mac[6];
WiFi.macAddress(mac);
clientName += macToStr(mac);
//if connected, subscribe to the topic(s) we want to be notified about
if (client.connect((char*) clientName.c_str())) {
Serial.print("\tMTQQ Connected");
client.subscribe("/test/light1");
}
//otherwise print failed for debugging
else{Serial.println("\tFailed."); abort();}
}
}
}
//generate unique name from MAC addr
String macToStr(const uint8_t* mac){
String result;
for (int i = 0; i < 6; ++i) {
result += String(mac[i], 16);
if (i < 5){
result += ':';
}
}
return result;
}
//------------------------------------------------------------------------------------------------------------------------------
