Mini-Chat
  • User avatar
    Siva Sankar - Mon Feb 18, 2019 4:42 am

    i am searching a think seriously, kindly clarify someone

  • User avatar
    Siva Sankar - Mon Feb 18, 2019 4:44 am

    i have a PLC with On board ethernet. is it possible to interface ESP8266 directly to it to establish wifi. which can eliminate the requirement of addition wifi router.

  • User avatar
    maorgo - Mon Feb 18, 2019 8:14 am

    hi, i`m trying to make a smart key chain using blynk app, arduino uno wifi(used as arduino uno), ESP8266-01 module and neo-6m gps module. i wanted to send to blynk server the gps coordinates and i cant do that because i try to compile the code as "generic ESP8266 module" so i could use the ESP8266 but than the gps wont work. how do i write code for that? thank you!

  • User avatar
    elhamkh - Tue Feb 26, 2019 3:49 am

    hi there i want to establish communication between two nodemcu esp8266 as client and server without home router by arduino IDE using UDP protocol . i uploaded codes on two nodemcu . server send packet to client but client is not able to send reply packet. i want to have bidirectional relation between them . what should i do ? please guide me .best regards . my codes will send to you after this message

  • User avatar
    giova90 - Fri Mar 01, 2019 8:27 am

    Hi, I want to connect 3 sensor with I2C protocol to esp8266, it is possible?

  • User avatar
    embedded - Sun Mar 03, 2019 6:38 pm

    Hi, I’m trying to customize the HTML page of the config portal for WifiManager to give it a new look. If I want to embed a logo or background image, where and hot to save the file to the module?

  • User avatar
    embedded - Sun Mar 03, 2019 6:38 pm

    Do I have to use the SPIFFS?

  • User avatar
    embedded - Sun Mar 03, 2019 6:42 pm

    By the way, I’m using PlatformIO with ESP8266 Arduino core. I don’t have the Arduino IDE so not sure how to do it

  • User avatar
    puguino - Sun Mar 03, 2019 11:59 pm

    embedded, you may consider to encode img as base64 into html

  • User avatar
    plzhelp - Wed Mar 06, 2019 9:26 pm

    hi is someone there?

  • User avatar
    amgu - Thu Mar 07, 2019 1:48 pm

    HI

  • User avatar
    amgu - Thu Mar 07, 2019 1:49 pm

    doubt regarding smart config esp

  • User avatar
    embedded - Thu Mar 07, 2019 5:49 pm

    Hi\

  • User avatar
    embedded - Thu Mar 07, 2019 5:49 pm

    Where I can find these libs:

  • User avatar
    embedded - Thu Mar 07, 2019 5:49 pm

    #include <PString.h> #include <Streaming.h>

  • User avatar
    Lakshan Fernando - Mon Mar 11, 2019 11:08 am

    Hi, has anyone tried ESPhttpUpdate.updateSpiffs with passing a WiFiClientSecure object successfully to update firmware over the air?

  • User avatar
    bort-x - Wed Mar 13, 2019 3:26 am

    is here anybody?

  • User avatar
    gbenna - Thu Mar 14, 2019 10:52 am

    I have an arduino uno 3 connected to my esp8266-esp01. I have a sketch on my arduino that read water level and then sends it to thingSpeak

  • User avatar
    gbenna - Thu Mar 14, 2019 10:56 am

    using software serial with AT commands. I wanted to be able to put in new ip and password so I connected up and put wifimanager on the esp8266 and everything worked out fine. I connected and put in new ip and password, esp8266 rebooted and connected to wifi. The problem is now how do I send sensor info to thingspeak since AT commands don’t seem to work anymore. Get error "’espData" was not declared in this scope. HELP

  • User avatar
    Krzysztof - Thu Mar 14, 2019 1:30 pm

    Gang, my ESP jumped into infinite loop during init.lua - how may I recover device ?

Who is chatting

No one is chatting  based on users active over the past 15 minutes

Refreshes every 30 seconds
Legend: Administrators, Global moderators