Mini-Chat
  • User avatar
    Lakshan Fernando - Mon Mar 11, 2019 11:08 am

    Hi, has anyone tried ESPhttpUpdate.updateSpiffs with passing a WiFiClientSecure object successfully to update firmware over the air?

  • User avatar
    bort-x - Wed Mar 13, 2019 3:26 am

    is here anybody?

  • User avatar
    gbenna - Thu Mar 14, 2019 10:52 am

    I have an arduino uno 3 connected to my esp8266-esp01. I have a sketch on my arduino that read water level and then sends it to thingSpeak

  • User avatar
    gbenna - Thu Mar 14, 2019 10:56 am

    using software serial with AT commands. I wanted to be able to put in new ip and password so I connected up and put wifimanager on the esp8266 and everything worked out fine. I connected and put in new ip and password, esp8266 rebooted and connected to wifi. The problem is now how do I send sensor info to thingspeak since AT commands don’t seem to work anymore. Get error "’espData" was not declared in this scope. HELP

  • User avatar
    Krzysztof - Thu Mar 14, 2019 1:30 pm

    Gang, my ESP jumped into infinite loop during init.lua - how may I recover device ?

  • User avatar
    JDC - Sat Mar 23, 2019 1:16 pm

    Using Putty through a PC. I don’t get anything but garbage. What needs to be done?

  • User avatar
    Marco3396 - Mon Mar 25, 2019 10:56 am

    hi, I have questions about a get request with Nodemcu. The request returns error 301 and sends me back to the same address but with https. In this case what needs to be changed

  • User avatar
    AbeeB - Mon Mar 25, 2019 12:02 pm

    I want to fetch audio(.3gp) from firebase and play in speaker through nodemcu.how should I do it.please help

  • User avatar
    Sawadee - Wed Mar 27, 2019 9:18 am

    Hi, New here, registered. I have made to replies to the same topic. Can’t see them. Is there a delay on Replies getting posted to the topic? Thanks

  • User avatar
    Adame542 - Sun Mar 31, 2019 11:45 am

    Is there a way I can use software serial in Adruino IDE on the ESP8266 module? The SoftwareSerial library doesn’t work. From what I have gathered, this is because the esp8266 module could be at 115200 baud rate which isn’t supported by the defualt SoftwareSerial library

  • User avatar
    Adame542 - Mon Apr 01, 2019 10:03 am

    or if my post could get approved within 3 days asking the same question so i can get my time sensitive project done... ^^^

  • User avatar
    JaydenLitjes - Wed Apr 03, 2019 9:38 am

    hey i need help please i want to make a someone from my nodemcu thingy but i need com3 but i dont see com3

  • User avatar
    mazeem - Sat Apr 06, 2019 5:06 am

    hi is there someone who can guide me the proper way to save the last state and Last Brightness of MQTT Dimmer.

  • User avatar
    mazeem - Sat Apr 06, 2019 5:06 am

    using eeprom

  • User avatar
    jonboy43 - Sun Apr 07, 2019 12:04 pm

    i want to remove an existing sketch. if i overwrite it will that overwrite everything, or do i need to somehow format the thing??

  • User avatar
    AdmiralPrabhak18 - Sun Apr 14, 2019 2:11 pm

    hey can anyone help me with a simple esp server question

  • User avatar
    flaviofaustini - Tue Apr 16, 2019 7:34 am

    can one use AT commands to set b/g/n radio mode?

  • User avatar
    flaviofaustini - Tue Apr 16, 2019 7:34 am

    Admiral ask your question

  • User avatar
    stevizzo - Tue Apr 16, 2019 6:07 pm

    hi

  • User avatar
    stevizzo - Tue Apr 16, 2019 6:07 pm

    hi anybody, just a question...i need to create a circuit for activating a dc motor from a switch button connected to a l298n and nodeMCU, do you have an idea on the circuit and sketch to make? Thanks very much, stefano

Who is chatting

No one is chatting  based on users active over the past 15 minutes

Refreshes every 30 seconds
Legend: Administrators, Global moderators