ESP8266 Community Forum

Txh ThomasW! I'll try this afternoon or tomorrow!

I confirm that more than half starts of NodeMCU 0.9.5 build 20150108 unsuccessful:

> 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб
NodeMCU 0.9.5 build 20150108 powered by Lua 5.1.4
lua: cannot open init.lua
> 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб
NodeMCU 0.9.5 build 20150108 powered by Lua 5.1.4
lua: cannot open init.lua
> 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб
NodeMCU 0.9.5 build 20150108 powered by Lua 5.1.4
lua: cannot open init.lua

I perform the checks run this firmware more than 100 times.
I think the problem with the power supply or reset the new ESP-03 module. However, the firmware NodeMcu 0.9.4 build 20141222 and NodeMCU 0.9.5 build 20150107 operate without this problem.

brig wrote:> 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб
NodeMCU 0.9.5 build 20150108 powered by Lua 5.1.4
lua: cannot open init.lua

Looks like a clean boot, doesn't it?
When my fails to boot, it just spills out a few random characters. As others noted, it is actually not a restart problem, but rather a cold boot problem. node.restart() seems to work all the time.

Fr4gg0r wrote:Looks like a clean boot, doesn't it?

Yes, this is when the unit is powered.
Is this ...

0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БCб 0‚~–4ы!‹“Y…$Ћ’2:’¶ЈяOґ:БBCб

...four attempts to power up.
node.restart () is always executed correctly.