Me again.
I'm having this annoying problem. I'm bootstrapping a custom config to 0xfa000 and it works just fine until i try to change something in the config from the CLI. For example i tried to set the baud rate to another value. If i do a "config-dump" i get this :
"cd
fuart.baud.0=14400 (14400/14400/0x3840)
total config entries: 1, flags: 4102"
Before this the cd looked like this:
cd
flags=16642 (16642/16642/0x4102)
wlan.mode=0 (0/0/0x0)
wlan.client.ssid=robot
wlan.client.passwd=robot
bridge.timeout=0 (0/0/0x0)
cmd.timeout=0 (0/0/0x0)
io.1.1.mode=5 (5/5/0x5)
io.1.1.llmode=4 (4/4/0x4)
io.0.3.mode=8 (8/8/0x8)
io.0.3.llmode=7 (7/7/0x7)
io.0.1.mode=8 (8/8/0x8)
io.0.1.llmode=7 (7/7/0x7)
bridge.port=23 (23/23/0x17)
io.0.4.mode=6 (6/6/0x6)
io.0.4.llmode=5 (5/5/0x5)
io.0.4.outputa.lower=0 (0/0/0x0)
io.0.4.outputa.upper=4294967295 (-1/4294967295/0xffffffff)
io.0.4.outputa.speed=0 (0/0/0x0)
io.0.5.mode=6 (6/6/0x6)
io.0.5.llmode=5 (5/5/0x5)
io.0.5.outputa.lower=0 (0/0/0x0)
io.0.5.outputa.upper=4294967295 (-1/4294967295/0xffffffff)
io.0.5.outputa.speed=0 (0/0/0x0)
io.0.12.mode=6 (6/6/0x6)
io.0.12.llmode=5 (5/5/0x5)
io.0.12.outputa.lower=0 (0/0/0x0)
io.0.12.outputa.upper=4294967295 (-1/4294967295/0xffffffff)
io.0.12.outputa.speed=0 (0/0/0x0)
io.0.14.mode=6 (6/6/0x6)
io.0.14.llmode=5 (5/5/0x5)
io.0.14.outputa.lower=0 (0/0/0x0)
io.0.14.outputa.upper=4294967295 (-1/4294967295/0xffffffff)
io.0.14.outputa.speed=0 (0/0/0x0)
pwm.width=10 (10/10/0xa)
io.0.2.mode=11 (11/11/0xb)
io.0.2.llmode=7 (7/7/0x7)
io.6.0.mode=6 (6/6/0x6)
io.6.0.llmode=5 (5/5/0x5)
io.6.0.outputa.lower=0 (0/0/0x0)
io.6.0.outputa.upper=4294967295 (-1/4294967295/0xffffffff)
io.6.0.outputa.speed=0 (0/0/0x0)
io.6.1.mode=6 (6/6/0x6)
io.6.1.llmode=5 (5/5/0x5)
io.6.1.outputa.lower=0 (0/0/0x0)
io.6.1.outputa.upper=4294967295 (-1/4294967295/0xffffffff)
io.6.1.outputa.speed=0 (0/0/0x0)
io.6.0.flags=128 (128/128/0x80)
io.6.1.flags=128 (128/128/0x80)
io.0.0.mode=3 (3/3/0x3)
io.0.0.llmode=3 (3/3/0x3)
total config entries: 50, flags: 4102
I think is from the way I bootstrap the config. I'm using sublime text as editor.
Thanks
Does the bootstrapped sector have exactly one empty line at the end? E.g.
line1\n
line2\n
\n
Are there no other control characters, like carriage return (CR, 0x0d, 13) in the sector? All lines should be terminated with only a newline (NL, 0x0a, 10).