**This is an old revision of the document!**
An opensource toolchain is available in https://github.com/pfalcon/esp-open-sdk. It is ready to run on Linux hosts only. If you don't use a Linux development machine, then the easiest way to build and to use the toolchain is to set up a Linux Virtual Machine (VM) on your development machine, as described in the following section. Another alternative is to use a low cost Linux board such as a Respberry PI2. Once you have your working Linux environment, setting up the toolchain is easy.
git clone --recursive https://github.com/pfalcon/esp-open-sdk
Run the make to install. This will take a long time, especially on a slow internet connection, so take a coffee
. Note that we recommend a standalone variant install as Espressif update their SDK quite frequently, keeping the log just in case you want to check it.
make STANDALONE=y |& tee make0.log
Finally log in again and run
xtensa-lx106-elf-gcc -v to validate the install. Note that if you type in toolchain commands at the command prompt, then you might wish to add frequent aliases for the toolchain gcc, ar, objdump etc. in your
.bashrc to save on typing, for example:
If you run Windows, OSX or Linux 64bit, then one of the easiest ways of setting up a development is to use a virtualization product to run a dedicated toolchain VM. There are a number of products available, but my personal preference is Oracle's VirtualBox as this is free, flexible and performs well on most common Intel / AMD platforms. This brief overview is written assuming the use of VirtalBox, but largely applies to setting up VM on most platforms.
Since nearly all toolchain work is done at the command prompt, it is simpler to configure your VM as a server instance and access it over SSH using the
ssh command on Linux or OSX and a product such as puTTY on Windows. If you decided to go this route then you don't need to learn the a Linux windows environment since you can access and manipulate both files and console sessions through your familiar Windows environment.
A simple VM with 384-512Mb RAM and 8Gb disk is easily sufficient to develop and build EESP8266 SDK-based images.
To keep thing simple I suggest using simple 32bit Ubuntu server configuration.
The first thing that you need to do is to download the VM product. In the case of VirtualBox, you don't need any of Oracle's closed source layered extension packs, so you can do a
sudo apt-get install virtualbox
on Debian and derived Linux systems such as Ubuntu. In the case of Windows and OSX, follow the instructions on the product's Downloads
page or follow one of the many step-by-step guides on Youtube and elsewhere.
You now need to download the Ubuntu Minimal installation CD for Ubuntu 14.04 LTS
(less than 40Mb).
VirtualBox has both a complete GUI
and commandline interface but again the simplest thing to do is to use the GUI
and follow one of the tutorials to create a new virtual machine (which I will call
, but you are free to choose whatever name your wish) (the bold options are non-default):
32-bit Ubuntu; 384Mb RAM
1 CPU; enable H/W virtualization assist if available
set minimal video memory (4Mb and no fancy features)
enable a IDE CD/DVD and map the
mini.iso to this.
enable and create a VDI-based dynamically allocated 8Gb SATA HDD. (You might want to place the VDI file in a specific work folder rather leaving it hidden in the VirtualBox folder hierarchy.)
add one NAT-based network adapter.
* You don't need any other virtual hardware or features, many some find the sheared folders feature worth installing. I don't bother nowadays and just use ''rsync'' / ''scp'' / ''sftp''.
NAT is described in the VirtualBox documentation, but in essence the VM host application acts as a router, so the VM doesn't have its own IP address. Instead you map host IP ports to client posts through the Network → Advanced → Port Forwarding function and a common port is to forward
10.0.2.15:22 so that doing an SSH to
localhost:2222 connects to the VM's default SSH port. Host and off machine process can only access the VM through a mapped port when the VM is running. (You will need to do an
ifconfig after you've built the machine to validate the guest's actual IP address.) Note that if you have multiple VMs, then you should use a unique port for each SSH eg. 2222 for VM1; 2322 for VM2, etc. This just stops you shooting yourself in the foot.
You now start VM through the GUI
and you will boot into the Ubuntu minimal install. There are again various YouTube and other tutorials which will take you through this (e.g. Ubuntu Server 14.04 LTS Network Installation Guide
), but what you need to do is to build a minimal server system that you can log onto over SSH.
Use the arrow / tab /enter keys to select Install
Choose your language
Chose your keyboard. Don't use automatic; just do a manual selection
Detect network and disable USB storage as you won't need it.
Give it the same host name as your VM machine name to keep things simple.
Choose a local Ubuntu mirror, and step through the menus until you get to
Download Installer Components
as you don't need any of these. The installer occasionally goes silent for 30-60secs, but then downloads all of the core components over network from the mirror. How long this takes depends on your internet bandwidth and how heavily the mirror is being hit, but 10-15 mins is typical. Time for a coffee
Now let the menu step you through the inputs. Nearly always the defaults apply. You need to choose a user name. Keep it the same as you use on your host. Don't bother encrypting your home directory. Use NTP to set the time.
Keep the disk partitioning simple: select guided
/ use whole disk
/ All files in One Partition
and install the base system. Another coffee or whatever, as this will chug along for another 20-60 mins. Sorry guys, but this is a LOT
less than Windows 10
When it comes to configuring the package manager, I untick everything and I then select no automatic updates, for reasons given below,
Only check Basic Ubuntu Server and openSSH Server on the Software Selection menu and hit continue to finish the install. You are then prompted to remove the media which you do virtually through a VirtualBox menu option, and the installer then reboots the machine.
At this point you can
sudo ipconfig to check the IP details and
sudo poweroff to shutdown the machine.
The basic server build is now complete.
I suggest that you run the server from now on in what is called headless mode – that is you start and stop the VM from a command line using
commands and just like a real server, you will only want to have the server console available for exceptions system maintenance. I use a set of aliases in my
on my laptop (Windows users can use
macros to achieve the same effect):
alias nodemcustart='vboxmanage startvm nodemcu –type headless'
alias nodemcusave='vboxmanage controlvm nodemcu savestate'
alias nodemcu='ssh -p 2222 localhost'
A major advantage of the network install is that the latest versions of all packages at the point of the build are loaded into the system, so there's no need to do the 100s of patch updates that you typically need to do with Windows. I am also going to lock the system down so that the only access to the system will be from your account on the host PC or laptop and that in effect no ports are exposed to the wider network. The only way that the VM can be security compromised is if the host account and PC have been compromised so there is no point in adding extra tiers of security within the VM.
Start the server and log on using your username / password combination. (If using SSH or puTTY for the first time google “putty using ssh keys authorizekeys” and read up on how public key based SSH access works and is configured). Now copy your public key to
~/.ssh/authorizedkeys. You should now be able to log off and log on from your host without needing to enter a password.
and chown 600 ~/.ssh/authorizedkeys
/etc/ssh/sshd_config and append the line
AllowUsers @10.0.2. to limit logon to access from the host PC. (You will neeed to use
sudo nano or
sudo vi to do this). And similarly do a
sudo visudo to add
NOPASSWD to the
%sudo groups as follows; this enables you to access root privileges without having to enter a password (and log off and on again to check that these are working OK.)
%admin ALL=(ALL) NOPASSWD: ALL
%sudo ALL=(ALL:ALL) NOPASSWD: ALL
* And lastly mangle your password so that only key-based access can work (replace
terry by your user account):
pwd=$(date|md5sum); echo -e “$pwd\n$pwd”|sudo passwd terry
* Now install all of the other core packages that allow you to build the toolchain, nodeMCU and
sudo apt-get install \
build-essential zip gdb git vim make unrar autoconf automake \
bison texinfo libtool gcc g++ gperf libc-dbg ncurses-dev \
lua5.1 lua5.1-doc luarocks lua-bitop lua-filesystem lua-md5 lua-posix lua-socket
# libexpat-dev flex bison texinfo libgmp3-dev libmpfr-dev libncurses5-dev
and you are good to go.
=======Using the Arduino IDE.=======
Another Integrated Development Environment (IDE) for programming in C++ and more easier for beginners is the Arduino IDE http://www.arduino.cc/en/Main/Software. Arduino IDE is an editor that is able to compile the code for us using Xtensa GCC toolchain, which is available at github as ESP8266/Arduino http:https://github.com/esp8266/Arduino. It also uses the ESPTool to automatically upload the hex to the SOC (system on chip). This repository provides several examples that you can put on the chip, and describes the install instructions for running it. They are as simple as adding the board manager url http://arduino.esp8266.com/package_esp8266com_index.json in the preference settings menu and install it using Tools→Board→Board Manager.
===== Notes =====
An arduino board is not needed as the ESP8266 has 16 times the memory and 5 times the speed.
32KB for the UNO Flash and it operates at 16 Mhz.
512 KB for the ESP8266 and it operates at 80 Mhz. (Up to 4Mb and 160Mhz on some)
Its limitation is its IO pins . Most have but one Analog pin but many Digital pins